Getting Started FRDM-PF1510EVM

最終更新日時： 2023-05-18 09:55:00サポート PF1510 for Low Power Application Processors

このドキュメントの内容

  • 1

    Get Started

  • 2

    Know the Board

  • 3

    Configure Hardware

  • 4

    Install Software

お客様の PF1510 for Low Power Application Processors

このドキュメントの内容

1. Get Started

The NXP analog product development boards provide an easy-to-use platform for evaluating NXP products. The boards support a range of analog, mixed-signal and power solutions. They incorporate monolithic integrated circuits and system-in-package devices that use proven high-volume technology. NXP products offer longer battery life, a smaller form factor, reduced component counts, lower cost and improved performance in powering state-of-the-art systems.

This page will guide you through learning about how to set up the FRDMPF1510EVM board.

1.1 Kit Contents/packing List

The FRDMPF1510EVM contents include:

  • Assembled and tested evaluation board in an anti-static bag
  • Cable, USB type A male/type mini B male 3 ft
  • Quick start guide

1.2 Required Equipment

This kit requires the following items:

  • 5.0 V DC power supply or USB with enough current capability (3.0 A for maximum performance)
  • KITPF1510GUI installed on a Windows PC
  • Optional voltmeters to measure regulator outputs
  • Optional oscilloscope
  • Mini USB Cables x2

1.3 System Requirements

The kit requires the following to function properly with the software:

  • USB-enabled computer running Windows XP, Vista 7, 8, or 10 (32 bit or 64 bit)

次へKnow the Board

2. Know the Board

2.1 Board Features

  • PF1510 PMIC
  • Integrated FRDM-KL25Z as a communication link between the EVB and a PC
Device Description Features
PF1510 power management integrated circuit (PMIC) for i.MX 7ULP, i.MX 6SL, 6UL, 6ULL, and 6SX processors
  • Three adjustable high-efficiency buck regulators with 1.0 A per regulator current capability
  • Three adjustable general-purpose linear regulators
  • Low dropout (LDO)/switch supply
  • Input voltage range on VIN: 4.1 V to 6.0 V
  • Double data rate (DDR) memory reference voltage
  • One time programmable (OTP) memory for device configuration
    		•

    2.2 Board Descriptions

    The FRDM-PF1510EVM boards serve as an evaluation platform that allows users to test and demo designs that incorporate the PF1510 PMIC. The evaluation board contains a pre-configured MC32PF1510A4EP device and provides numerous jumpers and test points that allow users to tailor the evaluation to their needs. The kit comes with an FRDM-KL25Z already mounted and loaded with compatible microcode. The primary function of the FRDM-KL25Z is to control communication between the evaluation board and a PC.

    2.3 Board Image

    The FRDM-PF1510EVM consists of a PMIC board with the FRDM-KL25Z as shown in the final assembly below.

    前へGet Started
    次へConfigure Hardware

    3. Configure Hardware

    3.1 Configuration Hardware

    The FRDM-KL25Z evaluation board was chosen specifically to work with the FRDM-PF1510EVM kit because of its low cost and features. The FRDM-KL25Z board uses the USB, built-in LEDs, and I/O ports available with NXPs Kinetis KL2x family of microcontrollers.

    The FRDM-PF1510EVM connects to the FRDM-KL25Z using the four-dual row Arduino R3 connectors on the bottom of the board.

    Suggested equipment's needed for test:

    • 5.0V power supply
    • Computer
    • Mini USB Cables x2

    3.2 Configuration Image

    3.3 Connect USB Cable

    Connect the mini-USB cable from a PC to the KL25Z USB port on the FRDM-KL25Z board. Connect the other end of the cable to a host computer.

    前へKnow the Board
    次へInstall Software

    4. Install Software

    4.1 Graphical User Interface

    Download and run SW for the FRDM-PF1510EVM

    Set up PF1510GUI on your computer

    1. Download PF1510 GUI for 32-bit or PF1510 GUI for 64-bit. Choose the 32-bit or 64-bit version regarding the system installed on your PC
    2. Extract all the files to any desired folder on your PC
    3. Plug the evaluation board
    4. Launch the GUI (no installation is necessary, GUI can be directly launched by clicking the file PF1510_x_Bx.jar)
    5. Configure the hardware
    6. Launch the PF1510 GUI

    Main log window indicate a connection

    前へConfigure Hardware
    次へDesign Resources

    Design Resources

    Board Documents

    Chip Documents

    Software

    Additional Resources

    Product Summary Page

    For PF1510 is located at PF1510

    Tool Summary Page

    The overview tab provides an overview of the device, product features, a description of the kit contents, a list of (and links to) supported devices, list of (and links to) any related products and a Get Started section.

    • On the Overview tab, locate the Jump To navigation feature on the left side of the window
    • Select the Get Started link, review each entry and download an entry by clicking on the title
    • After reviewing the Overview tab, visit the other product-related tabs for additional information:
      • Documentation: download current documentation
      • Software and Tools: download current hardware and software tools / Drivers
      • Buy/Parametrics: purchase the product and view the product parametric

        After downloading files, review each file, including the user guide which includes setup instructions.

      • Build a package: the bill of materials (BOM) and supporting schematics are also available for download in the Get Started section of the Overview tab

    For the Entire Solution

    In addition to our PF1510 Power Management Integrated Circuit (PMIC) for low power application processors page you may also want to visit:

    Product pages:

    Application Pages

    Hardware pages

    Software pages

    前へInstall Software